|
MORE ORNAMENTAL FENCE
REQUEST PRICE QUOTE
 Gaelic Fence
MATERIAL DESCRIPTION
The " GAELIC " fencing line is used in residential, industrial, commercial and institutional installations. The " GAELIC " fencing line is made of 6 gauge .192" ( 4.88 mm ) galvanized steel wire welded at each intersection. The width between the vertical lines is only 2" ( 50.8mm ) which makes it hard to gain a foothold. The distance between horizontals is 6" ( 152.4mm ) with grooves spaced evenly to add strength. The posts are square with the proper sizes depending on the height specified.
Where more security is needed posts are extended 18" ( 457.2 mm ) at 45 degrees, thus adding 12" ( 304.8 mm ) to the height of the fence. Three strands of barbed wire can be attached to the arm & razor coil added to it for a powerful visual deterrent.
MATERIAL SPECIFICATIONS
Wire diameter 6 gauge .192" ( 4.88mm ) - Mesh size 2" x 6" ( 50.8mm x 152.4 mm ) Tensile strength 71.400 to 100.000 Psi - Welded strength 1015 lbs ( 462 kg ) ( 44.88 Newton ) as per ASTM a 185. The mesh is hot dipped galvanized as per ASTM a641 class 1 coating, weight of .5 oz/ft. The steel posts are square with a minimum tensile strength of 45.000 PS ( 310 MP ).
Posts are manufactured as per ATM A.D. - G
Inches
|
mm
|
Gauge
|
Lbs / ft
|
Kg
|
2"
|
50.8
|
14 ( 2.03 mm )
|
2.164
|
.982
|
2 1/2"
|
63.5
|
14 ( 2.03 mm )
|
2.733
|
1.240
|
3"
|
76.2
|
12 ( 2.64 mm )
|
4.286
|
1.944
|
4"
|
101.6
|
10 ( 3.42 mm )
|
5.770
|
2.617
|
6"
|
152.4
|
7 ( 4.50 mm )
|
14.230
|
7.004
|
Sections are fastened to the front of the post ( this adds greater strength ) by using a special zinc die cast connectors and fastened with tamper proof 1/4" rivets.
Finish :All components shall go through the following stages
1) Rinsed and cleaned with clear water
2) Phosphate treated to etch the surface & Rinsed again with clear water
4) Components are oven dried prior to powder coating
5) Polyester powder is then applied by the electrostatic spray process to a thickness of 2.5 mils ( .0635 mm ). The metal is then oven heated at 450 degrees for 14 minutes.
Standard Colors Unavailable : Black, Chocolate, Ensor Green, Olive Green and White. Custom colors are available upon request.
 Sentinel Fence
Boundary high SECURITY FENCING is available in heights up to 15ft. And 6'8 wide panels. The system consists of posts and panels and is modular. No welding is required in the field.
Fabrication
Pickets - are 2 1/2" wide and are rolled formed with grooves for additional rigidity and strength. The SENTINEL and SENTINEL plus styles have a triple pointed spear at top. The CENTURION and CENTURION PLUS styles have a square top. Space between pickets is 3 13/16" on bottom and 2 3/4" on top for the SENTINEL style. Space between pickets is 3 13/16" for the CENTURION style. Picket material is 10 gauge , hot rolled with a deflection not to exceed 3/8" when a point load of 562 pounds is applied in the center of a 24" span. Minimum tensile strength is 50,000 PSI yield, with a 40,000 PSI . Pickets are welded with 8" of weld per picket to two 2" x 2" x 1/4" horizontal steel angles. 2" x 2" angle brackets are secured to the web of the post with 3/8" stainless steel carriage bolts and break away tamper - resistant aluminum nuts. Both styles can be ordered for underground installation to prevent entering or leaving the secured area other options are the SENTINEL and CENTURION PLUS, which have a 3/4-9-11 expanded metal welded in the back for additional security..
Fence posts are 4" I-Beams weighing 7.7 lbs. Per foot., with pre punched slotted holes in the web for the rail bracket supports. Posts should be set 3 ft. In the ground. For surface mounting, we can supply a base plate.
Gates - are available both swinging and rolling type.
Finish - 3 finishes are available
In galvanized steel with a G90 zinc content ( .90 oz/ft. ), then powder coated with a 2 - 3 mil bonded polyester powder. Standard colors are : Black, Chocolate, Ensor Green, Olive Green and White. Other colors are available upon request at additional cost. Components shall go through a 3 stage wash, then primed prior to a factory finish with a thermo setting of polyester powder and bonded at 450 - 500 degrees for 12 - 14 minutes.
All members are hot dipped galvanized after fabrication with a zinc coating of 1.50 oz/ft and left as it is.
Hot dipped galvanized after fabrication and welding, then powder coated as in paragraph # 1 above
 Barrier Fence
BARRIER STYLE fence is designed as the ultimate barrier where most other fences are not acceptable. BARRIER FENCES are available in heights up to 15 feet and width up to 6'8". Custom Size may be available on request.
Fabrication
Pickets are 2 1/2" wide and are roll formed with grooves for additional rigidity and strength. Spacing between pickets is 2 1/8" thus making it virtually impossible to climb. On the inside of the section, a 5/16" round bar is welded flush, spaced every two feet of height, thus making it very hard to spread the pickets apart. Picket material is 10 gauge, hot rolled with a deflection not to exceed 3/8" when a point load of 1,050 pounds in the center of a 24" span. Minimum tensile strength is 50,000 PSI yield, with a 40,000 PSI. Pickets are welded with 6" of weld per picket to a 2 1/2" x 1/4" hot rolled flat. 2" x 2" angle brackets are secured to the web of the post with 3/8" stainless steel carriage bolts and break away tamper resistant aluminum nuts.
POSTS
BARRIER FENCE POSTS are made of 4" I- beams weighing 7.7 lbs/ft., with pre punched slotted holes in the web for the rail bracket supports. Posts should be set 3 feet in the ground. For surface mounting, we can supply a base plate.
Gates
BARRIER GATES are available both swinging and rolling types
Finish - 3 finishes are available
In galvanized steel with a G90 zinc content ( .90oz./ft.) Then powder coated with a 2-3 mil bonded polyester powder. Standard colors are : Black, Chocolate, Ensor Green, Olive Green and White. Other colors are available upon request at additional cost. Components shall go through a three stage wash, then primed prior to a factory finish with a thermo setting of polyester powder and bonded at 450 - 500 degrees for 12 - 14 minutes.
All members are hot dipped galvanized after fabrication with a zinc coating of 1.50 oz /ft. And left as they are.
Hot dipped galvanized after fabrication and welding, then powder coated as in paragraph # 1
 Alpha Fence
MATERIAL SPECIFICATIONS
The “ALPHA" line of fencing is strong durable and attractive. It is ideal for commercial and residential applications. The "ALPHA" line is available in the following:
1) Steel hot dipped galvanized to ASTM-123,
2) Polyester powder coated.
MATERIAL - STEEL BARS
Vertical and Horizontal members are hot rolled carbon steel bars as per ASTM - A569 and hot dipped galvanized to ASTM - 123
POST SPACING
Spacing is 78 1/4" (1988mm) between posts. Custom panels are available when desired.
HEIGHTS
Available from 2' to 15' ( 60.96cm to 457.20cm ).
FINISH
All polyester powder coated components shall go through a 5 stage process:
Rinsed and cleaned with clear water .
Phosphate treated to etch the surface.
Rinsed again with clear water
Components are oven dried prior to powder coating.
Polyester powder is then applied by the electrostatic spray process to a thickness of 2.5 mils ( .0635 mm ) . The metal is then oven heated at 450 degrees ( 232 Celsius ) for 14 min.
Standard colors available : Black, Chocolate, Ensor green, Olive Green and White.
Custom colors are available upon request.
Assembly
Sections are bolted to posts with four 3/8" carriage bolts and a break away aluminum nuts (vandal proof).
Gates
Gates are manufactured with a 2" x 2" frame. Hinges are barrel type, 7" long with a 3/4" stainless steel pin. Latches are fulcrum type. All gates can be polyester powder coated regardless of size.
ALPHA X
.
ALPHA XV
Alpha XX
Alpha XXV
Alpha XXX
Alpha XXXV
Alpha XL
LOUVER GATES SPECS
Deluxe Railing
Poseidon style front & side view
Triton Style
Eros Style
Eros Details
|